The Efficacy and Biopharmaceutical Properties of a Fixed-Dose Combination of Disulfiram and Benzyl Benzoate.

Scabies and hair lice are parasitic diseases that affect human skin and hair, respectively. The incidence and resistances of these infections are increasing. Tenutex® (disulfiram and benzyl benzoate emulsion) is an alternative to standard insecticides to avoid resistances. The aim of the work is to evaluate the transdermal absorption and the in vitro efficacy against scabies and hair lice after different exposition times. Dermatomed human skin was used to assess the dermal absorption using a validated High Performance Liquid Chromatography (HPLC) method. HEK001 keratinocytes were used to evaluate the cytotoxicity of benzyl benzoate. Only benzyl benzoate was able to cross the skin, but it did not show cytotoxicity at any of the tested concentrations. The product efficacy was tested on Psoroptes ovis after direct contact and after administration on sheep skin explants at different contact times. Permethrin/malathion-resistant strains of Pediculus humanis capitis adults and eggs were directly exposed to Tenutex, and the vitality and hatchability, respectively, were evaluated. The anti-scabies study demonstrated that exposure for 6 or 24 h completely eradicated the parasite. The pediculicidal activity of Tenutex exhibited superior efficacy than standard treatment on resistant lice. The positive results obtained suggest that Tenutex® is a good treatment option, especially in drug resistance situations.

Pilot Equivalence Study Comparing Different Batches of Topical 0.025% Capsaicin Emulsion: Product Microstructure, Release, and Permeation Evaluation.

The European Medical Agency (EMA) has issued a draft guideline on the quality and equivalence of topical products. The equivalence for complex semisolid formulations involves several steps: the same quantitative content, the same microstructure, the same release, and permeation profile. In this paper, several batches of a low strength topical product, which we used as a reference/comparator product, were evaluated according to the recommendations of the EMA draft guideline. The batches were 0.025% capsaicin emulsions from the same manufacturer that were evaluated in terms of droplet size, X-ray diffraction patterns, rheology, release, and permeation profile. The generated data revealed a large batch-to-batch variability, and if the EMA guideline was applied, these batches would not be considered equivalent, although they were produced by the same manufacturer. The result of this work illustrates the difficulties in obtaining equivalence according to the current draft guidelines. It also highlights that the equivalence guidelines should consider the variability of the comparator product, and in our opinion, the guidelines should allow for claiming equivalence by comparing the limits in the variability of the data generated for the comparator product with the limits in the variability of the data generated for the intended equivalence product.

Transparent films based on PLA and montmorillonite with tunable oxygen barrier properties.

Polylactide (PLA) is viewed as a potential material to replace synthetic plastics (e.g., poly(ethylene terephthalate) (PET)) in food packaging, and there have been a number of developments in this direction. However, for PLA to be competitive in more demanding uses such as the packaging of oxygen-sensitive foods, the oxygen permeability coefficient (OP) needs to be reduced by a factor of ~10. To achieve this, a layer-by-layer (Lbl) approach was used to assemble alternating layers of montmorillonite clay and chitosan on extruded PLA film surfaces. When 70 bilayers were applied, the OP was reduced by 99 and 96%, respectively, at 20 and 50% RH. These are, to our knowledge, the best improvements in oxygen barrier properties ever reported for a PLA/clay-based film. The process of assembling such multilayer structures was characterized using a quartz crystal microbalance with dissipation monitoring. Transmission electron microscopy revealed a well-ordered laminar structure in the deposited multilayer coatings, and light transmittance results demonstrated the high optical clarity of the coated PLA films.

Fusion of nonionic vesicles.

We present an experimental study of vesicle fusion using light and neutron scattering to monitor fusion events. Vesicles are reproducibly formed with an extrusion procedure using an single amphiphile triethylene glycol mono-n-decyl ether in water. They show long-term stability for temperatures around 20 degrees C, but at temperatures above 26 degrees C we observe an increase in the scattered intensity due to fusion. The system is unusually well suited for the study of basic mechanisms of vesicle fusion. The vesicles are flexible with a bending rigidity of only a few k(B)T. The monolayer spontaneous curvature, H(0), depends strongly on temperature in a known way and is thus tunable. For temperatures where H(0) > 0 vesicles are long-term stable, while in the range H(0) < 0 the fusion rate increases the more negative the spontaneous curvature. Through a quantitative analysis of the fusion rate we arrive at a barrier to fusion changing from 15 k(B)T at T = 26 degrees C to 10 k(B)T at T = 35 degrees C. These results are compatible with the theoretical predictions using the stalk model of vesicle fusion.

Cryo-fracture TEM: direct imaging of a random mesh phase.

A novel and a simple method that allows direct imaging of viscous samples by cryo-TEM (cryo-transmission electron microscopy) is presented. A fracture on the vitrified sample is created in a controlled way. In the fracture, some edges are thin enough to allow direct imaging in transmission mode. The method was used to directly image a nonionic surfactant lamellar phase where a random mesh structure is formed at lower temperatures (<10 degrees C). A so-called random mesh phase, characterized by the presence of perforated surfactant bilayers, is imaged here for the first time. Images from the mesh structure are compared with images from the classical lamellar structure formed at room temperature.

Vesicle formation from temperature jumps in a nonionic surfactant system.

When heating a dilute sample of the binary system of tetraethyleneglycol dodecyl ether (C12E4) and water from the micellar phase (L1) into the two-phase region of a lamellar phase (L(alpha)), and excess water (W) vesicles are formed. During heating, one passes a region of phase separation in the micellar phase (L1' + L1'') where the initial micelles rapidly fuse into larger aggregates forming the concentrated L1 phase (L1'') with a structure of branched cylindrical micelles, a so-called "living network". The static correlation length of the micelles are increasing with increasing concentration, from ca. 10 nm to 80 nm in the concentration range of 0.0001 g/cm3-0.0035 g/cm3. The overlap concentration was determined to 0.0035 g/cm3. When the temperature reaches the L1' + L(alpha) region the network particles transform into bilayer vesicles with a z-average apparent hydrodynamic radius in the order of 200 nm depending on the composition. The size of the final vesicles depends on the extent of aggregation/fusion in the L1' + L1'' region and hence on the rate of heating. The aggregation/fusion in the L1' + L1'' is slower than diffusion-limited aggregation, and it is shown that 1/100 of the collisions are sticky results in the fusion event.